Nilfisk-alto DPA6000 Manuel d'utilisateur

40 BIT ENHANCEDSTEREO POWER AMPLIFIERDPA6000User's ManualLTORwww.altoproaudio.comEnglishVersion 1.0 MAY 2005

2>. The PC Editor should now load. A welcome screen will appear. This closes after 5 seconds (or click onit). Select NEW from the FILE menu. A wind

105.5 Help FileThe HELP file accessible from within the PC Editor will be updated as necessary. Since software updates after theprinting of this manua

5.3 First Steps with the PC EditorTo avoid accidentally overwriting an existing PRESET, it is important that you follow the correct routine when ini-t

12RS232RS232 (9Pin-F)PIN 5 PIN 3 PIN 2(RXD) PIN3(GND) PIN5(TXD) PIN2 PIN 3(RXD)PIN 2(TXD)PIN 5(GND)The wire must be changed between 2,3 pin.9 PIN9 PIN

channel 1 or 2 will be output from both channel 1 and 2 simultaneously. Details refer to the chapter 9.- Bridge ModeIn this mode, the signal input int

RS485 INRS485 OUTRS232SERIAL PROTCH1BALANCEDINPUTPARALLELOUTPUTCH2BALANCEDINPUTPARALLELOUTPUTSERIALMODEL

RS485 INRS485 OUTRS232SERIAL PROTCH1BALANCEDINPUTPARALLELOUTPUTCH2BALANCEDINPUTPARALLELOUTPUTSERIALMODEL1+ 1-POS NEGBRIDGEMONO2+ 2-POS NEG1+ 2+POS NEG

RS485 INRS485 OUTRS232SERIAL PROTCH1BALANCEDINPUTPARALLELOUTPUTCH2BALANCEDINPUTPARALLELOUTPUTSERIALMODEL1+ 1-POS NEGBRIDGEMONO2+ 2-POS NEG1+ 2+POS NEG

1710. TECHNICAL SPECIFICATIONSMODEL8 ohms per channel(EIAJ)4 ohms per channel(EIAJ)8 ohms, 1KHz, 0.1%THDBridge Mono ModeDistortion (SMPTE-IM)Frequency

1811. WARRANTY1. WARRANTY REGISTRATION CARDTo obtain Warranty Service, the buyer should first fill out and return the enclosed Warranty Registration C

SAFETY RELATED SYMBOLSCAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENThis symbol, wherever used, alerts you to the pre-sence of un-insulated and dangerous vo

SEKAKU ELECTRON INDUSTRY (H.K.) CO., LTD.No. 1, Lane 17, Sec. 2, Han Shi West Road, Taichung 40151, Taiwanhttp://www.altoproaudio.com Tel: 886-4-22313

2PREFACEDear Customer:For LTO AUDIO TEAM,music and audio are much more than a job, they are a passion and an obsession!By purchasing our LTO products

TABLE OF CONTENTS1. INTRODUCTION...

RS485 INRS485 OUTRS232SERIAL PROTCH1BALANCEDINPUTPARALLELOUTPUTCH2BALANCEDINPUTPARALLELOUTPUTSERIALMODEL1+ 1-POS NEGBRIDGEMONO2+ 2-POS NEG1+ 2+POS NEG

RS485 INRS485 OUTRS232SERIAL PROTCH1BALANCEDINPUTPARALLELOUTPUTCH2BALANCEDINPUTPARALLELOUTPUTSERIALMODEL1+ 1-POS NEGBRIDGEMONO2+ 2-POS NEG1+ 2+POS NEG

4.3 Channel SelectionThere are total 3 options available (CH1, CH2, CH1+CH2), you can apply these effect settings on either orchannels.both selectedSe

116. PARAMETER MENUS DESCRIPTION- HUM CANCEL: allows the modification of the dynamic NOTCH filter parameters. The graph included shows thefilter respo